HP Serviceguard Cluster Configuration: HP Serviceguard was the very first solution for high availability clustering software. Serviceguard uses. Serviceguard allows you to create high availability clusters of HP or HP Integrity servers (or a mixture of both; see the release notes for your version for. HP Serviceguard Cluster Commands. This section includes the Serviceguard clustering commands. Closed /usr/local/bin/sudo /usr/sbin/cmviewcl -v. Output.

Author: Kazit Gusida
Country: Dominica
Language: English (Spanish)
Genre: Love
Published (Last): 13 September 2018
Pages: 23
PDF File Size: 14.60 Mb
ePub File Size: 6.14 Mb
ISBN: 511-9-86915-432-3
Downloads: 35537
Price: Free* [*Free Regsitration Required]
Uploader: Nerisar

Serviceguard allows you to create high availability clusters of HP or HP Integrity servers or a mixture of both; see the release notes for your version for details and restrictions.

HP Serviceguard

A high availability computer system allows application hpp to continue in spite of a hardware or software failure. Highly available systems protect users from software failures as well as from failure of a system processing unit SPUdisk, or local area network LAN component. In the event that one component fails, the redundant component takes over. Serviceguard and other high availability subsystems coordinate the transfer between components.

A Serviceguard cluster is a networked grouping of HP or HP Integrity servers or bothknown as nodeshaving sufficient redundancy of software and hardware that a single point of setviceguard will not significantly disrupt service. A package groups application services individual HP-UX processes together. There are failover packages, system multi-node packages, and multi-node packages:.

The typical high availability package is a failover package. It usually is configured to run on several nodes in the cluster, and runs on one at a time.

If a service, node, network, or other package resource fails on the node where it is running, Serviceguard can automatically transfer control of the package to another cluster node, allowing services to remain available with minimal interruption. There are also packages that run on several cluster nodes at once, and do not fail over. These are called system multi-node packages and multi-node packages. A system multi-node package must run on all nodes that are active in the cluster.

  EXECUTIVE SEDUCTION JENNIFER PROBST PDF

If it fails on one active node, that node halts. System multi-node cluxter are supported only for HP-supplied applications. A multi-node servicegaurd can be configured to np on one or more cluster nodes. It is considered UP as long as it is running on any of its configured nodes.

Each package has a separate group of disks associated with it, containing data needed by the package’s applications, and a mirror copy of the data. Note that both nodes are physically connected to both groups of mirrored disks. In this example, however, only one node at a time may access the data for a given group of disks. In the figure, node 1 is shown with exclusive access to the top two disks solid lineand node 2 is shown as connected without access to the top disks dotted line.

Similarly, node 2 is shown with exclusive access to the bottom two disks solid lineand node 1 is shown as connected without access to the bottom disks dotted line.

Mirror copies of data provide redundancy in case of disk failures. In addition, a total of four data buses servicceguard shown for the disks that are connected to node 1 and node 2. Note that the network hardware is cabled to provide redundant LAN interfaces on each node.

Any host system running in a Serviceguard cluster is called an active node. Under normal conditions, a fully operating Serviceguard cluster monitors the health of the cluster’s components on all its active nodes.

  DIMITRIS RIZOPOULOS PDF

Most Serviceguard packages are failover packages. When you configure a failover package, you specify which active node will be the primary node where the package will start, and one or more other nodes, called adoptive nodesthat can also run the package. After this transfer, the failover package typically remains on the adoptive node as long the adoptive node continues running.

Configuring a two node serviceguard Cluster (part 1) | ~Unix and Linux~

If you wish, however, you can configure the package to return to its primary node as soon as the fluster node comes back online. Alternatively, you may manually transfer control of the package back to the primary node at the appropriate time. In order to remove all single points of failure from the cluster, you should provide as many separate power circuits as needed to prevent a single point of failure of your nodes, disks and disk servicetuard.

Each power circuit should be protected by an uninterruptible power source. Event Monitoring Service EMSwhich lets you monitor and detect failures that are not directly handled by Serviceguard. HP recommends these products; in conjunction with Serviceguard they provide the highest degree of availability.

Complete book in PDF. Using this site means you accept its terms.

Business