Service Manual, Elna DE Details. Elna Model DE Serger Machine Service Manual, 20 Pages. The physical copy of the instruction manual is a soft cover. Full text of “Elna Serger Instruction Manual dse de e” IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic. Hi there, Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this.
|Published (Last):||26 August 2010|
|PDF File Size:||15.12 Mb|
|ePub File Size:||9.78 Mb|
|Price:||Free* [*Free Regsitration Required]|
Search the history of over billion web pages on the Internet. Read all instructions before using the machine. To reduce the risk of electric shock: Always replace the bulb with the same type rated 15 Watts maximum.
Pay close attention when the machine is used by or hear children. Use only attachments recommended by the manufacturer as contained in this manual. Return the machine to the nearest 614se dealer or service center for examination, repair, electrical or mechanical adjustment. Keep ventilation openings of the sewing machine and foot control free from accumulation of lint, dust and loose cloth. Special care is required around the sewing needle and moving blade.
It may deflect the needle causing it to break.
Always store the machine indoors. To unplug, grasp majual plug not the cord. To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the lena, reverse the plug. Jf it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way. Dear Customer, You have chosen an overlook sewing machine of the highest quality, which will make your hours of sewing become hours of pleasure and relaxation.
We congratulate you on your choice and hope that it will give you lasting satisfaction. Before you start to use your machine, please take a few minutes to study this instruction manual. You will find that it will assist you in your complete understanding of the functions and capabilities of your overlock machine. If you wish to obtain more information, please do not hesitate to contact your dealer who is mabual qualified to answer your questions.
Furthermore, your dealer should also be contacted for all technical interventions which are under warranty. Thank you for choosing a series overlocker. The electric foot control regulates motor and sewing speeds. The greater the pressure on the control, the higher the speed. Press preferably rlna the sole of the foot, not with the toes. Extension Discs 2 transparent discs are supplied with the machine. Place them at both ends of the spool pin base, as illustrated, to avoid thread tangling. Thread Guide Pole Pull the thread guide pole up to the highest position.
Cone Holders and Caps Both industrial and domestic type thread spools can be used on the machine. For industrial spools, the cone holders a. For spools with lena large diameter, place the cone holders higher up on the spool pins or place them with the widest end on top see illustrationso that the spools can be seated firmly on the spool pin base.
Place the spools perpendicularly. When using domestic type spools, remove the cone holders and place the caps b over the spools of thread. To disengage the lever cfirst open the front door, raise the presser foot and bring the needle s to the highest or lowest position by turning the flywheel towards to you by hand.
Pull the knob d first to the right, and then swing it down. To engage the lever cmaunal the same steps, pull the knob d to the right, and then swing it up. They are needles for domestic use and can also be used with all ordinary household sewing machines.
For normal or thick fabric, use size 90 and for sheer fabric size 80 needles. Loosen the needle clamp screws a with the Allen screwdriver bto remove the old needles. Hold the new needles with the flat side away from you and push them up as far as they will go. Tighten the screws firmly. A Presser Foot Lever To raise the presser foot, swing the lever c down and you can see the round mark in red, as illustrated. To lower the presser foot swing the lever c up. For sewing fluffy or fairly thick fabric, the extra lift 2 mm will be available by swinging the lever c down again.
Snap-on Sewing Foot Mabual remove the foot, raise the needle bar and presser bar to their highest positions, then push the lever d on the shank. To lock the foot on to the shank, place the foot under the shank and lower the presser bar.
Follow the threading paths carefully, in accordance with the charts inside the front door, in the sequence It is important that threading is carried out in the following sequence: Upper looper thread – Yellow thread guides 2. Lower looper thread – Green thread guides 3. Right 64de thread – Red thread guides 4. Left needle thread – Blue thread guides Incorrect threading will result in several problems such as skipped stitches and thread breakage. Threading the Upper Looper – Coloured yellow on the chart and on the thread guides.
Draw the thread from the spool, as shown on the diagram, pass the thread through the guides A and B.
Draw the thread down between the two tension discs of the yellow tension control, then through the other thread guides and the hole in the upper looper, steps C to G. Draw the thread back under the presser foot, leaving about 10 cm of thread to the left.
Elna De Overlocker Manual · GitBook (Legacy)
Threading the Lower Looper – Coloured green on the chart and on the thread guides. Follow a similar procedure as above, and also shown on the diagram, steps a to e.
Bring the lower mqnual to its right position by turning the flywheel by hand. Push the lever f down and hook the thread on the guide gpush the lever f up to the woking position, then pass the thread through the eye h at the far right end of the looper.
Threading the Right Needle – Coloured red manuwl the chart and 6114de the thread guides. Raise the needle bar to the highest position. Pass the thread through the guides A to C. Pass the thread through the open slot of 61d4e take-up lever cover D and down to the guides E and F.
Finally thread the right needle from front to back, then under the foot, leaving about 10 cm of the thread to the left. Threading the Left Needle – Coloured blue on the chart and on the thread guides. Follow a similar procedure as above, and also shown on the diagram, passing the thread through the thread guides and left needle tension and finally thread the left needle, steps a to f.
Before staring to sew, check again that all the threads have been properly passed through every thread guide and are well 6144de between the two tension discs of each tension control, to ensure good sewing results. Should it be necessary mxnual any time to re-thread the lower looper, always remove the thread from the needles first, to avoid tangling.
First release Model or loosen the tensions, then pull the looper threads gently behind the needle until the knots have passed through. Next pull the needle thread gently and bring the knots to the front of the needles. Cut the thread at both ends of the knots and pass them through the respective eyes of the needles. It is advisable to raise the tension release lever so that the two tension discs of the red and blue tension controls manuql.
You can pull the needle threads in front of the needles easily Model Make sure that the front door is closed. Pass the 4 threads under the foot as shown in the drawing. Lower the presser foot, make a few stitches by hand, turning the flywheel towards you without fabric under the foot. Press on the foot control to make 3 to 4 cm of overlock chain, holding the threads on the left. The machine is now ready to sew.
Do not pull the fabric; guide it gently. When you reach the end of the fabric, do not raise the presser foot, continue sewing at low speed for about 10 cm beyond the end of the fabric so that the machine produces a chain of thread.
A manual for elna 614DE – Elna Sewing Machines
Then cut the thread with the thread cutter see illustration. Epna are then ready to start the next seam. You can start overlocking from the edge of the fabric just by feeding it into the front of the lowered presser foot. Do not raise the presser foot at the end of a seam but always sew a chain of thread at least 10 cm long. Safety Device Model The front door is provided with a safety device. If it is open, the machine will not work.
Turn the tension knobs referring to the numbers on the dials; turning elja a higher number will increase the thread tension and to a lower number decrease it. A balanced tension a – b The needle threads lie on the top side of the fabric just like a row of normal straight stitches on the upper looper thread, and just visible in the lower looper thread on the underside of the fabric.
If the thread tensions are too tight, the fabric will pucker.
ELNA 614DE Manuals
V Stitch Length Most overlook sewing projects can be done with the stitch length set at 2 to 3. However, you can easily change the stitch length by shifting the stitch length slide a between 0. Your machine is equipped with two feed dogs a and beach of which moves independently. However, when the differential feed control slide c is set at 1.
By pushing the differential feed slide c down to a higher number, the front feed dog a moves the fabric faster, as shown. This helps to prevent knitted or stretch fabrics from puckering and waving during sewing. By pushing the differential feed slide c up to a lower number, the front feed dog a moves the fabric more slowly, as shown. This helps to prevent sheer and lightweight fabrics from puckering.